Hitec X1 AC Plus: Single Port AC/DC Chargers Bedienungsanleitung

INSTRUCTION MANUAL

10FeaturesOptimized Operating Software The X1 “auto” feature sets the charge and discharge current for you automati-cally, preventing overcharging whi

11FeaturesProcessing Time LimitProtect your battery by setting a maximum time limit for charging and dis-charging.Input Power MonitoringThe X1’s input

12TO AVOID SHORT CIRCUITS, ALWAYS CONNECT THE CHARGE LEADS TO THE CHARGER FIRST, AND THEN TO THE BATTERY. REVERSE THE SEQUENCE WHEN DISCONNECTING THE

13The X1 o ers the following lithium charge modes: Charge, Balance Charge, Fast Charge, Storage and Discharge. BEFORE SELECTING A CHARGE MODE, IT IS

14Lithium Charge Mode (cont.)LithiumPress the ► button once to enter the “CHARGE” screen. Press the ► button again and the amp rate value will begin 

15This function is for balancing the voltage of individual Lithium-polymer bat-tery cells while charging. In order to use the Balance Mode, the batter

16Charging in Fast Charge Mode allows for a shorter charge time and will result in a slightly reduced charging capacity. To achieve maximum charge cap

17Once charging has commenced, the charger will display the following real-time information: Battery type/cell count, charging current, battery voltag

18First, select the correct battery type by following the instructions on page 13. Once you have set the correct battery type, press the button once

19If you plan to discharge your battery to reach safe storage levels we strongly recommend that you use Storage Mode. In very few instances should dis

2Table of ContentsIntroduction ... 3Warnings and Safety

20Press the ► button once to enter the “CHARGE“ screen. Now use the ✚ or ▬ buttons to change from “CHARGE“ mode to “DISCHARGE“. Press the ► button ag

21The X1 o ers the following NiCd/NiMH charge modes: Charge, Discharge and Cycle. BEFORE SELECTING A CHARGE MODE, IT IS CRITICAL THAT YOU SELECT THE

22BEFORE YOU BEGIN DISCHARGING YOUR BATTERY, MAKE SURE YOU HAVE READ AND UNDERSTAND ALL OF THE WARNINGS AND SEFETY INFORMATION CONTAINED ON PAGES 47.

23The X1 makes cycling of NiCd/NiMH batteries easy. The process of discharg-ing and recharging (cycling) can be achieved automatically with one simple

24BEFORE YOU BEGIN CHARGING YOUR BATTERY, MAKE SURE YOU HAVE READ AND UNDERSTAND ALL OF THE WARNINGS AND SEFETY INFORMATION CONTAINED ON PAGES 47.Af

25Pb Charge Mode (cont.)Pb Disharge ModePb (Lead-Acid)Press and hold the ► button and charging will begin.Once charging has commenced, the charger wil

26LithiumSave/Load DataThe Save Data and Load Data programs make it easy to store and load charge and discharge pro les for up to 5 batteries. Data c

27Save Data Program (cont.)Load Data ProgramLithiumSave/Load DataPress the ► button again and the voltage rate value will begin  ashing. Use the ✚ or

28LithiumAdditional Features & SettingsPress the button repeatedly until you reach the “USER SET PROGRAM->“ screen.Battery TypePress the ► b

29Safety TimerPress the ✚ button once to advance to the “Safety Timer“ screen. This screen will allow you to set the maximum charge time in order to p

3IntroductionCongratulations on your choice of the Hitec X1 charger from Hitec RCD USA. The Hitec X1 is a high-performance, microprocessor controlled

30LithiumAdditional Features & SettingsPress the ► button once to and the timer value will begin  ashing. Use the ✚ or ▬ buttons to change the ti

31LithiumAdditional Features & SettingsThe Temperature Cut-o is turned on or o with the use of the optional temperature probe by contacting th

32LithiumAdditional Features & SettingsWhen the charge process starts, the integrated safety timer starts to run simul-taneously. If an error occu

33A beep sounds to con rm the user’s operation every time a button is pressed. The buzzer or melody sounds at various times during an operation to co

34Reverse PolarityThe battery/charger connections (red/black) are reversed.Connection BreakThe battery connection has been diconnected. Short CircuitT

35Over Temperature ErrorThe internal temperature of the charger is too high. Allow the charger to cool down.Control FailureThe charger has malfunctio

Warranty and Service (cont.)THIS WARRANTY IS IN LIEU OF ANY AND ALL OTHER WARRANTIES, WHETHER FOR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE

These warnings and safety notes are of the utmost importance. You must fol-low these instructions for maximum safety. Failure to do so can damage the

5 A Never attempt to charge or discharge the following types of batteries:• A battery  tted with an integral charge circuit or a protection circuit•

Warnings and Safety NotesLiPo LiIon LiFe NiCd NiMH PbNominal Voltage3.7V/cell 3.6V/cell 3.3V/cell 1.2V/cell 1.2V/cell 2.0V/cellMax. Charge Voltage4.2V

7Always refer to recommendations from your battery manufacturer for your speci c battery type and size before initiating a charge or discharge proces

8Charger Layout1. Hitec X1 AC Plus Charger2. AC Power Cord3. DC Power Cord4. 18AWG Wire Charging Cable5. Balancing Board Cable6. Universal Balan

9Speci cationsDC Input (11-18V) Balance SocketAC Input (100-240V, 50/60HZ) Temperature Sensor PortCharging OutputCharger LayoutAC Input 100 - 240 Vol